Lippert-components FT-CG9 User Manual download pdf

HAPPIJAC

Frame Mount

Camper Tiedown System

Models: FT-UT9 & FT-CG9

IMPORTANT: READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING:

Installation of this camper tiedown system is similar for all truck models. However, while the basic

steps are the same, the details vary from truck to truck Read instructions completely and note correct

installation options at each step for the truck on which tiedown are being installed. These instructions

will show installation of one side only. Both sides install identically.

STEP 1 –[Hardware Kit A] Attach both backing (guide) plates to stabilizer bar. Using

#10 x ¾” sheet metal screws. See diagrams below for specific locations.

Note: The 4 large round holes in guide plate must be to the outer ends of the assembly

at both ends.

1988 & Newer Chev / GMC

1980 – 1998 Ford

1999 & Newer Ford

F-250

(Over 8500 GVW) & F-350

1994 & Newer Dodge Ram

STEP 2 –[Hardware Kit C] Attach frame brace to backing plate by inserting the flat head,

square shouldered plow bolts through the countersunk hole in frame brace and securing

with flat washer, split lock washer and nut. See diagrams below for specific locations.

Note: Do not tighten the nuts at this time. They will be tightened at a later step.

1999 & Newer Ford

F - 250

(Over 8500 GVW) & F- 350

1999 & Newer Chev / GMC

(Silverado / Sierra)

Center Slots

Inner Slots

1988 & Newer Chev / GMC

(CK Classic Series Only)

Round Holes

1980 – 1997 Ford

1994 & Newer Dodge

(8500 GVW +)

COMPANY

FRONT ANCHOR INSTALLATION

REAR ANCHOR INSTALLATION

NOTE: Rear anchors are installed in the end of the bumper. There is no

precise mounting location since a variety of bumpers may be

installed. The general guidelines are as follows:

1. Mounting location should be as flat & vertical as possible.

2. Be sure no moldings or bumper caps interfere with

the removable coupler.

3. Check back side of selected mounting location to ensure adequate

access for tightening nut.

4. Choose a location as far back as possible from the front edge of bumper

while giving consideration to the other criteria listed above and center

punch and drill a

/8” pilot hole, then enlarge to

/2”.

Install Anchor Bolt with 2” fender washer, lock washer & nut.

Flat edges of Anchor Bolt must be horizontal.

Remove

coupler

when not

in use to

prevent loss.

Flats Horizontal

Place well back

From front edge

Of bumper

505 N. Kays Drive, Kaysville UT 84037

Phone: (801) 544-2585

Fax: (801) 546-5241

Email: [email protected]

Web Address: www.happijac.com

All defective material must be returned to the factory via prepaid shipment. Upon inspection and determination of claims

warranted, the factory will repair/replace the material at no charge and return the repaired/replaced material to the

customer with delivery charges prepaid by Happijac via common carrier of Happijac's choosing. Upgrades and changes

to shipping mode resulting in additional shipping costs shall be at customers expense.

WARRANTY CLAIMS:

All products manufactured by Happijac Co. are warranted to the retail customer for one year from date of purchase

against defects in material or workmanship. Any defective part(s) will be repaired or replaced (at Happijac’s option)

without charge, when returned transportation prepaid.

There are no other expressed warranties except as set forth above and any implied warranties are limited in duration to

that of the expressed warranty. This warranty does not cover any damage due to misuse, negligence, or accidents. There

is no warranty covering consequential damages, incidental damages, or incidental expenses including damage to

property.

This warranty gives you specific legal rights. You may have other rights which may vary from state to state.

WARRANTY INFORMATION

TERMS OF THE WARRANTY:

ftut9instruct014304

1 2

HAPPIJAC 1
Mounting Holes 2

Summary of Contents

Page 1 - HAPPIJAC

HAPPIJACFrame Mount Camper Tiedown SystemModels: FT-UT9 & FT-CG9IMPORTANT: READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING:Installation of th

Page 2 - Mounting Holes

...A BSTEP 5 – Drill four 7/16" holes through guide plate and bed front wall using the four large round holes as a drill guide. These holes ali

Related models: FT-UT9

Comments to this Manuals

No comments

Lippert-components FT-CG9 User Manual

Browse online or download User Manual for Hardware Lippert-components FT-CG9. Lippert Components FT-CG9 User Manual

Summary of Contents

Related models: FT-UT9

Comments to this Manuals

Related products and manuals for Hardware Lippert-components FT-CG9